Laptop Liquid Cooling Cooler Kit Water Pump Reservoir CPU GPU 275mm Heat Sink. This is a notebook water-cooled suit, the product is novel and easy to install. Compared with the air-cooling heat dissipation, the cooling effect of the water-cooled package is more significant.
Small size, no space, can be placed on the desktop. Customliquid cooling can give you much better cooling performance compared to all inone cooling systems and traditional air coolers as you can make specific tweaks to your system to have it perform better. The kit contains all the bits you need to customise your water cooling set up and have it match the rest of your system. 275 120 32 mm/ 10.8 4.7 1.3 in. Composition: single layer flat tube, flat tube 18.
Rated voltage: 12V motherboard small 3-pin plug. Input current: 0.8A ±10%. Motor operating speed: 5600RPM ± 5%. 71 56 46 mm/ 2.8 2.2 1.8 in (not include brackets and connectors).
Wiring color definition: red positive / black negative / white speed. Ceramic bearing, graphite bushing, very quiet, no water idling during use. Bracket hole distance: starting from the center of the hole, width 51.50mm, length 31.50mm. 120 120 25 mm/ 4.7 4.7 1.0 in.Fan speed: 1200 ± 10% RPM. Maximum static pressure: 1.703mm-H20. Working voltage: 10.8-13.2VDC. 12 5.8 5.8 cm/ 4.7 2.3 2.3 in. Material: PMMA + anode aluminum. Intermediate transparent acrylic outer diameter: 50mm. Hole position: G1/4 thread 6. Equipped with adjustable plastic clips1. 1 Water Tank (Equipped with adjustable plastic buckle 1). Lock the two fans with the M332 screws on the water line. Use the M335 screw to lock the water row bracket on the water line.
The other side of the second step uses the M312 screw to fix the water row bracket and the water drain. Lock the 90° bracket with an M414 screw + M4 nut on an I-bracket. Lock the type I bracket of step 4 with the M410 screw + M4 nut under the water pump.
Lock the adjustable plastic buckle of the water tank with another M410 screw + M4 nut on the other type I bracket. Lock the pump of step 5 and the adjustable plastic clip of step 6 with M312 screws on the water line. Install the quick screw, pagoda, 90° elbow and plug on the water drain, water pump and water tank respectively. Install the quick-turn nut and seal ring on the short straight hard pipe and connect the water pump and the water tank together. Install one plug and two quick turns on the water flow meter.
Quickly screw the nut and seal ring on the other two hard tubes and connect them with the water pump, water flow meter and water drain to complete the installation. Instead of leaving negative/neutral feedback or opening a dispute.
Our listing price includes the value of goods, packaging cost, and export. Please check with your country's. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails.
If you are satisfied with our service, pls. Our aim is to provide Top Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We will always do our up most to exceed your expectations in customer service, communication and dispatching of your orders. The item "600L/H Liquid Cooling Complete Kit Water Pump Reservoir CPU GPU 275mm Heatsink" is in sale since Friday, December 14, 2018.
This item is in the category "Computers/Tablets & Networking\Computer Components & Parts\Fans, Heat Sinks & Cooling\Water Cooling". The seller is "besttrade360" and is located in Shenzhen. This item can be shipped worldwide.