IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V

IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V

IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V. For CNC Router Engraving Milling Machine. Free Duty & Free VAT to below Europe Countries. A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece, H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland, P ortugal, R omania, S lovakia, S lovenia, S pain, S weden, S witzerland, U nited Kingdom. 1 x 1.8KW ATC (Automatic Tool Change) water cooled spindle motor 220V 5.4A 24000rpm.

Ps (without include ISO20 tool holder). 100% Brand New and High Quality!! The bearing of spindle use grease lubricated angular to contact bearings, can be achieved lifelong lubricating within the life cycle.

The spindle use forced coolling mode to coolling motor, front and rear bearings. Coolant flow through the reasonable arrangement cycle watercourse of the spindle body, thus can take the heat generated of the spindle rotation speed, to achieve thermal equilibrium, let spindle temperature within a certain constant value. External cooling device effect:maintaining a constant temperature of the coolant. The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification), you can read it anytime if you need to protect the motor temperature. The tool clamping methods:this spindle built-in automatic tool change device, shank form is ISO20. Automatic tool changer electric spindle parametric curve graph. Automatic tool changer electric spindle technical parameters. Spindle blowing dust/seal gas pressure (MPa). Spindle gas seal gas flow.

Spindle static state pulse (µm). Motor windings Pressure test (V/M). 1000V/1 minute withstanding Voltage test. For castings, aluminum, glass, etc. The system must ensure that the cooling water temperature of supply spindle is between 24-28 degree.

Usually setting the flow switch in return pipe of the cooling system, to ensure the supply of spindle cooling water. In order to prevent water or impurities enters internal of the spindle, spindle will have gas sealing device, the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration. The quality requirement of gas which is used in gas seals. Pressure dew point: <7.5degree (0.7MPa).

Running-in program instructions Only all monitoring issued no failures operational signals, at the same time, all safety devices have been installed and working properly, then allow start spindle. Note: new or spindle which is not used for a long time must to be running slowly. First, start run spindle for half an hour as 25% of the maximum speed, then increase to 50% of the maximum speed, to run 15 minutes, finally, increase to maximum speed.

Its need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department. Package and check if there are some damages before sign, if there are some d. The item "IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V" is in sale since Thursday, May 9, 2019.

This item is in the category "Commercio, ufficio e industria\Fornitura industriale\Macchinari e attrezzature". The seller is "powace08" and is located in Prague. This item can be shipped to European Union member countries.
IT1.8KW 80mm Spindle Motor Water Cooled ATC Automatic Tool Change CNC Kit 220V