This cools only the engine block. On average, this kit will take 2-4 hours for installation. This kit comes with everything needed for installation.Nothing more will be needed. Will this kit fit my application? Will fit Volvo Penta applications years 2000-present. Fits small block GM engines (4.3L, 5.0L, 5.7L, 6.2L). Half Kit (cools block only).
CONVERSION KIT FITS This conversion kit fits 2000-present Volvo Penta 5.0l (305 CID) and 5.7l (350 CID) engines. It will also fit other small block Chevy-based engines were an on-engine installation is not practical. See space requirements to confirm that it will fit within the engine compartment. COOLING SYSTEM TYPE Off-engine remote mounted.
The engine block protected by freshwater system; the exhaust manifold and exhaust elbow remain on raw water system. CONVERSION KIT Kit includes heat exchanger, heavy-duty translucent plastic expansion tank plus other components necessary to complete conversion. Hoses and related hose clamps are not included. Some components from engine are reused.Heat Exchanger and Brackets are finished in black. HEAT EXCHANGER Heat exchanger is shell and tube type with special high capacity design. All copper alloy construction made to the highest industry standards. Includes dual demountable end covers for easy clean out. SPACE REQUIREMENT Before purchasing this system, make sure there is enough room in the engine compartment to accommodate the heat exchanger, expansion tank, and necessary components. Heat exchanger is 4.13" diameter x 20" overall length (Approximately the size of two rolls of paper towels placed end to end). Heat exchanger should be mounted as close to the front of the engine as possible. The mounting bracket is included with the kit. Note: The heat exchanger must be below the level of the filler neck on the thermostat housing. The heat exchanger may be mounted on any horizontal or vertical surface. Monitor Products, Inc recommends a vertical mounting on the starboard side and slightly in front of the engine, it allows for easier hose routing and draining of the raw water side during winterization. Expansion tank has to be mounted close to level with the filler neck.
The expansion tank must be mounted as close to the engine as possible. It is recommended that you request a copy of the installation instructions and review them completely and do a mock installation using two rolls of paper towels placed end to end to represent the heat exchanger before purchasing to insure you have the space available to install the kit. This will also give you a chance to determine approximate hose lengths that will be needed for installation. The mounting locations should not hinder the opening or closing of the hatch. Do not drill into fuel tanks, water tanks, or any other critical areas.Do not contact any belts or fuel lines. COOLING SYSTEM CAPACITY The heat exchanger will maintain coolant temperatures in the 160-170. F thermostat included in kit. The system has a cooling capacity safety margin higher than industry standards.
HEATER SYSTEM HOOKUP Heaters such as galley water heaters and cabin heaters are easily connected to the system by utilizing the cooling system bypass connections. INSTALLATION TIME Average installation time is approximately 2-4 hours, assuming new engine and normal accessibility. Allow additional time for filling and testing.
Installation skills are typical of most do-it-yourself boat owners. Complete illustrated installation instructions are included in kit. For Domestic United States Customers. For International Customers & US Customers in HI & AK. From anywhere in Europe, Australia, South America, Africa, Japan, etc.This is the cheaper option. This option is more expensive but can be effective for customers in a rush.
Item that you're interested in (item # works too). We'll get back to you quickly with your quote! Some locations may take longer depending on ocean liner availability and destination port. There is no question too small.
Your 100% satisfaction is always our goal. We make every effort to carefully describe each item. Warranties cannot be extended for any matter.We are able to provide contact information for those companies should the need arise. Questions As stated above, we are delighted to answer any questions you have. Service & Support We believe in good communication!
As such we are quite prompt with replies to emails we receive, even to the point of using wireless to insure continuous monitoring of all aspects of our business operations. Upon completion of the telephone order an invoice will be emailed or mailed to you (whichever you prefer).
Occasionally we include these costs as a special - and when we do, it will be clearly stated in the item description or title. We want our customers to be completely satisfied with both the service and product that we provide.
We produce high quality marine engines and components. No matter what part you need give us a call, we stock them all! We have the best prices for marine engines and parts in the industry. There's nothing worse than a boat with a dry hull.
Attention Sellers - Get Templates Image Hosting, Scheduling at Auctiva. The item "New 5.7L, V8 Marine Engine Fresh Water Kit/Closed Cooling kit- Volvo years 00-up" is in sale since Tuesday, January 8, 2019.
This item is in the category "Vehicle Parts & Accessories\Boats Parts & Accessories\Boat Engines & Motors". The seller is "centerstateengine" and is located in Ocala, Florida. This item can be shipped worldwide.