380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit

380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit
380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit

380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit

380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit For CNC Router Milling Engraving Machine. A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece, H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland, P ortugal, R omania, S lovakia, S lovenia, S pain, S weden. We will send this item from Germany Warehouse by DHL/DPD to EU Countries. 1 x 4.5KW ATC Automatical tool change Air cooled spindle motor 380V 24000rpm 800Hz. 1 x 5.5KW VFD Inverter 380V (VFD have been set well to run this spindle).

1 x BT30-ER25 Tool Holder with 45 degree pull stud. ATC Automatic Tool Changer Air Cooled Spindle Motor 380V.

The bearing of spindle use grease lubricated angular to contact bearings, can be achieved lifelong lubricating within the life cycle. The spindle use forced coolling mode to coolling motor, front and rear bearings. Coolant flow through the reasonable arrangement cycle watercourse of the spindle body, thus can take the heat generated of the spindle rotation speed, to achieve thermal equilibrium, let spindle temperature within a certain constant value.

External cooling device effect:maintaining a constant temperature of the coolant. The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification), you can read it anytime if you need to protect the motor temperature.

The tool clamping methods:this spindle built-in automatic tool change device, shank form is BT30. 4.5kw air-cooled automatic tool change spindle is a high-end woodworking company designed to develop.

High-power electric spindle bearings imported fom Germany, high-precision bearings, high precision, long life. The electric spindle fan cooling with Road gas seal structure, automatic tool changer with bt30 shank, feast. Automatic tool change and improve the efficiency of the automated processing. Proximity switch and push button switch.

Spindle blowing dust/seal gas pressure. Spindle gas seal gas flow. V/1 minute withstanding Voltage test. Woodworking machinery, polishing industry, etc. When the spindle rotates, the rear fan system must be started to ensure the correct supply voltage and the supply voltage is 12V. In order to prevent water or impurities enters internal of the spindle, spindle will have gas sealing device, t.

He gas seal machine must be started start with the machine at the same time. And the need to go through.

The quality requirement of gas which is used in gas seals. Only all monitoring issued no failures operational signals, at the same time, all safety devices have been installed and working properly, then allow start spindle. Is not used for a long time must to be running slowly. First, start run spindle for half an hour as 25% of the maximum speed, then increase.

50% of the maximum speed, to run 15 minutes, finally. Eed to check the temperature of the spindle. Spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department. Protection of impurities into the spindle.

Piston reset 0.35-0.45MPa. Spindle power lines with thermistor. Spindle tool change signals 24V. Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection. The spindle built two sensors. Wiring Diagram is as follows. Response broach knife signal, when the. Response loose knife signal, when the. 5.5KW 380V Fuling VFD Frequency Inverter Variable Frequency Driver. It could adapt to the dust working environment. This VFD can be used for constant torque loads (such as hard starting: Air compressors, HVAC units) and variable torque loads (such as pumps, fans, etc). It can be used as a motor speed control and a phase converter. The input for this VFD is 1 or 3 phase as you like.

You can control different speed when you use this VFD. Most of our customers bought this VFD from us to use for: Lathes, Mills, Car Hoists, Pumps & Conveyors, etc. This item uses Sine wave PWN(SPWM) for the control system and performance excellently. He usages of the product and warnings.

When installed, please carefully, pay attention to personal safety and to avoid injuries occurred during the installed process. Do not use any tools tapping spindle. Do not use sandpaper and grinding wheel to wipe or grind in. Axis core and taper hole.

Use special removal tool to remov the lock nut and the tool. Untrained personnel can not disassemble and operate electric spindle. Attention to maintenance and maintenance. Electric spindle storage temperature is 20.

85%, to allow time to store up to three months. Electric spindle most suitable ambient temperature is 20. Bearing life can achieve the desired optimum value.

The power cord must take waterproof measure, electric spindle housing must be grounded. Electro-spindle must not exceed nameplate parameters. Not allowed to use any mechanical way to forced braking. Should wipe spindle taper, then smear with rust oil.

Workplace must be clean, there should be strict dust control measures to prevent foreign matter enter the spindle. Product common malfunctions&method of exclusion. Electric spindle is not running after boot. No inverter power output or set incorrectly. Check that VFD supply three-phase output voltage and setting method.

Spindle plug is not inserted. Check the electrical spindle plug and connection. Shutdown after a few seconds of the boot.

Start time is too short. Electric spindle high temperature cause line package insulation damaged. Electric spindle lose phase to run, then cause overcurrent protection blackout. Check the electric spindle connection. Electric spindle smoking or the housing hot after a few second of the boot.

Inverter output voltage, frequency are not match the use of electric spindle voltage and frequency. Check the VFD and the spindle voltage, frequency. The VFD is not set correctly. Locking nut loose when it is started. Change the direction of rotation.

Spindle have big noise and vibration. Precision of parts damaged, its effect dynamic balance. Locking nut loose when it is stoped. Stop time is too short. Item must be in it's original condition and no physical damage. We are happy to have your questions. We are here to solve them by the friendly and quick ways. The item "380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit" is in sale since Thursday, March 18, 2021. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Variable Frequency Drives".

The seller is "kuku218" and is located in Frankfurt. This item can be shipped to European Union member countries.


380V BT30 ER25 ATC 4.5KW Water Cooling Spindle Motor VFD &5.5KW inverter CNC kit