CNC 2.2KW ER20 Water Cooling Spindle Motor VFD 220V Kit For Engraving Metal Mill. For CNC Router Milling Engraving Machine. NO Duty & NO VAT to Below Europe Countries.1 x 2.2KW ER20. 1 x 80mm spindle bracket.
1 x 75W Water pump. (1mm, 2mm, 3mm, 3.175mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm, 12mm, 13mm each 1pcs). 2.2kw ER20 Waterproof spindle motor 220V Water-cooled Carved metal.
4 bearings(C7005x2 + C7003x2), P4 class. Professional aviation Interface, Interface 1234 marked 123 respectively connected to the inverter output end of the (U, V, W), 4 is blank.Wood, Aluminum, Stone, Metal, glass, PVC industry etc. 1 In use, must first connect the cooling water pipe, make spindle connect cooling water and then start. 2 Before driving, turned by hand spindle.
If sensory block is not flexible, you should troubleshoot, and then check the direction of rotation of the spindle from the spindle end to see if the match should rotate counterclockwise power wiring should be changed to make it consistent. 3 Before driving, cooling water for grinding workpiece cant be in the front end of the spindle cover, to prevent the front bearing cover slot inlet burning motor and bearing.
The motor must not enter the water, after turned on of the motor, when you live in grinding the workpiece to open the grinding of workpieces coolant. First off the workpiece coolant shutdown, and then close the spindle motor. 1 Motorized spindle by medium frequency power supply rated voltage, frequency should be consistent with electric spindle technology parameters, motorized spindle rotational speed can change the frequency to adjust, also directly proportional voltage change.2 When the spindle is temporarily not in use, should use compressed air to blow the coolant water, to avoid rusting, plug the hole. Spindle surface should be coated with anti rust oil. The shaft end protecting device, placed in dry place. 3 If replacement the spindle of bearings, best professional and technical personnel from the replacement. Use special tools, stator coil does not to be removed.
The inverter uses a simplified vector control technology, with extensive application of functional blocks. Can be the whole frequency band of torque automatic compensation, to compensate for the output torque to meet the user requirements for high torque; to improve the dynamic response and motor control features. Have a proportional, integral and differential (PID) control function of the closed-loop control, can be used for process control , such as constant pressure water supply. Built-in the function of the textile-specific swing band.Fast current limit (FCL) function, to avoid undue running trip. Acceleration / deceleration ramp features have a programmable smoothing function.
Prevent the speed lose during over-voltage, in running the inverter automatically limit the increase of DC bus voltage. Fault and fault query monitoring features. Built-in serial communication interface, using standard modbus communication protocol.There are vents or ventilation devices in indoor places. Ambient temperature -10 C 40 C. If the ambient temperature is bigger than 40 C, but lower than 50 C, may take off the cover board of inverter or open the front door cabinet, in order to reduce temperature. Try to avoid high temperature and wet places, humidity less than 90%, and without dewfall. Away from air pollution such as flammable and corrosive gases, liquids. No dust, floating particles of fiber and metal. It is not allowed that the inverter falls down or suffers from fierce impact or the inverter installed at the place that vibration frequently.
Keep away from the electromagnetic radiation source. 75W CNC spindle motor water pump 3.2m 220VAC. Fit for 0.8kw, 1.5kw, 2.2kw, 3kw, water cooled spindle even 4kw and 5.5kw too. Out dia (D1):11.5mm.
Run-out tolerance 0.1mm (0.006) First class 1065 carbon steel Hardened & precision groun. Please give us the opportunityto resolve any problem when you have, we concern your problem and we will try our best to resolve it. Item must be in it's original condition and no physical damage.When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos. The item "CNC 2.2KW ER20 Water Cooling Spindle Motor VFD 220V Kit For Engraving Metal Mill" is in sale since Thursday, April 15, 2021. This item is in the category "Equipamiento y maquinaria\Automatiza., motores y ejes\Motores eléctricos\Motores de uso general". The seller is "powace1515" and is located in Lausanne. This item can be shipped to European Union member countries, United Kingdom.