Item Type: Cooling Fan Kit Material: ABS, Brass, Aluminum Alloy, Acrylic Main Accessories: 10 Pipes Integrated Water Drain Assembly with Fan: Interface: Straight Mouth Fan Size: Approx. 12cm / 4.7in Fan Interface: Big 4pin Water Drain Specification: Approx. 120mm / 4.7in Drain Size: Approx.152mm / 6.0in Approx. 60mm / 2.4in Approx. 120mm / 4.7in GPU Water Block Assembly (with A Pack of Mounting Screws): Material: Brass, Aluminum Alloy Contact Copper Surfaces Size: Approx. 50mm / 2.0in A Pack of SC600 Water Pump Components, Pagoda Screws: Voltage: 12V DC, 3 Pin Plug on the Motherboard Power: 10W Head: 3 Meters Stream Rate: 500 Liters / Hour 140mm Cylindrical Water Tank Components: Water Tank Material: Acrylic, ABS Water Tank Diameter:Approx. 50mm / 2.0in Water Tank Height: Approx.
140mm / 5.5in With A Pair of Black Water Tank Brackets, A Pair of Silver Brackets, A Pack of Mounting Screws Hose (Transparent) Assembly (A Pack of Accessory Copper Mounting Screws): Hose Material: TPE Hose Length: Approx. 2m / 78.7in Hose Size: Inner Diameter: Approx. 8mm / 0.3in Outer Diameter: Approx.
10mm / 0.4in Water Cooled Liquid Filling Device. Show that the water block is installed 26. Install the graphics card back to the computer motherboard and fix the effect picture 27. Fix the cooling fan to the cooling water drain (note: the fan is sent to the radiators) 28. The effect diagram of fixing the heat sink on the chassis 29.
The display diagram of the follow-up connection between the pump and the water tank. In the actual situation, you can change the follow-up method, and go back and install it at will. Fix the water tank rack in the proper position of the chassis, and then snap the water tank into the buckle 31. All accessories are fixed, measure the length of the pipe at each position of the pipeline, and then cut the pipe 32.
Put the tube skull on both ends of the tube 33. Connect the weft waterway like this, and then put the pipe skeleton on the joint with pliers 35. Then check whether each waterway is installed properly to avoid water leakage 36. Add water and coolant, fill the water tank for the first time, and then turn it on, it will become less during the cycle, fill it up again, make sure the air inside is drained, and then plug the plug 37. Connect the power supply of the water pump to the position of the previous CPU fan, and the big 4pin interface of the fan can be found on the power supply to insert it.2 x 120 Pagoda Water Drain (with One 12cm Fan). 1 x GPU Water Block. 4 x Finger Screw Nut. 1 x 140mm Cylindrical Water Tank. 2 x Black Water Tank Bracket.
Screw on the nut, the progress of the two screws is the same, then install the pagoda connector, and tighten. Instead of leaving negative/neutral feedback or opening a dispute. Our listing price includes the value of goods, packaging cost, and export. Please check with your country's. We will reply your message within 48 hours.If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails.
If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy.
We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders. This item is in the category "Computers/Tablets & Networking\Computer Components & Parts\Fans, Heatsinks & Cooling\Water Cooling". The seller is "goodfeeling360" and is located in this country: CN. This item can be shipped worldwide.